RX8Club.com

RX8Club.com (https://www.rx8club.com/)
-   RX-8 Discussion (https://www.rx8club.com/rx-8-discussion-3/)
-   -   Instalation of Stainless Steel Exhaust Shields/Protectors (https://www.rx8club.com/rx-8-discussion-3/instalation-stainless-steel-exhaust-shields-protectors-37402/)

NoPistonsHere 08-24-2004 03:31 PM

Instalation of Stainless Steel Exhaust Shields/Protectors
 
1 Attachment(s)
Is there a Thead on how to instal these Stainless Steel Exhaust Shields/Protectors, Already did a search. The instructions I got are really complicated. To install these I have to disconect the Battery??? I was like what the!!! Do you have to take the whole rear bumper and lights off just to put on the Stainless Steel Exhaust Shields/Protectors ???? Maybe I was miss reading them, cause it was just before going to bed. I am here at work, and I am going over it off the top of my head, and it seems to be a big do it yourself job for just two items.

mysql101 08-24-2004 03:34 PM

in your bumper, are little screw thingies. You turn it with a screw driver, and pop it out. Then the black area around your exhaust tips will unclip and slide out. You then screw the exhaust finishers into it, and slide it back. Snap it in, put back the screw things and you're done.

I don't see a reason to disconnect the batt.

FONZIE 08-24-2004 04:19 PM

1 Attachment(s)
http://www.mazdatrix.com/faqrx8/exhfinish.htm :rolleyes:

NoPistonsHere 08-24-2004 04:23 PM

That's what I was thinking, cause the shrouds have to come out when installing an Exaust system, when using 2 floor jacks to elevate the 8. I will Post the Directions Rosenthal Mazda sent (Comically Confusing) .

Thanks Jason Hamilton

Ryan

NoPistonsHere 08-24-2004 04:34 PM


Originally Posted by FONZIE


Did a search already, but got better results from you!!! Fonzie :rolleyes:

Jeffjett 08-24-2004 04:37 PM

They are called exhaust finishers, and there is a DIY available for installation. Insert exhaust finishers in search engine or look in DIY.

mysql101 08-24-2004 04:46 PM


Originally Posted by NoPistonsHere
That's what I was thinking, cause the shrouds have to come out when installing an Exaust system, when using 2 floor jacks to elevate the 8. I will Post the Directions Rosenthal Mazda sent (Comically Confusing) .

Thanks Jason Hamilton

Ryan

The only reason I know about how to remove them is because I removed one when installing my borla. After removing one, I noticed that they didn't need to come out for the install afterall. Just take the old exhaust off the hanger and you can slip it out no prob.

I had the car up on two ramps (rear wheels only), not a lot of room to move.

NoPistonsHere 08-24-2004 05:15 PM

cool, I am still waiting on lift usage from my co worker. I have my Racing beat Exaust in my bedroom waiting to be installed

FONZIE 08-25-2004 08:20 AM

I installed them myself in my driveway. It was VERY easy to do.

NoPistonsHere 08-25-2004 10:03 AM

I installed them last night, longest part was waiting for my Cousin to come over with the Drill.

Rx8 Club is the Bomb!!!

Special Thanks to All on this Thread,

Ryan


All times are GMT -5. The time now is 08:39 AM.


© 2024 MH Sub I, LLC dba Internet Brands