june 1,2008 rx8/rx7 Ne BBQ meet, LYndhurst N.J
 

Hey guys
well you asked for it so we are putting this together.
funds are being collected this week on tuesday night @ local meet.exact location will be posted by either maverick or chrism which are local.
post away

ill be there at the meet late..i gotta work.but count me in..

i was talking to klepto about this earlier....i think we should be doing this mid afternoon...just so we can have the most people and make it a bbq lunch deal....would any one be able to help him out with a midpipe install too?.....some one got ramps they can bring?

midpipe should be easy
no need for ramps just jack it up with 2 side jacks.
and yes
mid afternoon meet
say 2-3 pm ?

im off wednesday if ya wanna get together and do the shopping....since i have the rxtahoe...

I have tools at my house that you guys can use. I would be happy to do it for you if you can chip in on a new set of Mechanix gloves as I cut my hands up big time doing Kel's coilovers this past weekend.

The good ol RX7 scissor jack works just fine


FYI - here is the location for the BBQ. For those of you not familiar with the area, we are probably going to have the staging point be at the Starbucks where we normally meet at and drive over to the bbq. Either Chris or I will scout it out this week to make sure everything is kosher for the weekend.

Here it is in relation to the starbucks:
http://img.photobucket.com/albums/v4...spottopark.jpg

Here are the two park spots. We will probably be using the north park.
http://img.photobucket.com/albums/v4...hurstparks.jpg

sounds like a plan to me.....

thanks guys....looking forward to it this saturday. Chris I'll meet you and we can roll out I guess.

I got some stands and a jack and the oem 8 jack as well so getting it up in the air should be fine. Any help I can help is greatly appreciated. If anyone has a breaker bar I think that would be key.

have a breaker bar.

awesome will make like easier and make the install quicker.

its sunday isnt it?

i got 2 jack stands i can bring

I think so....

Yes, this sunday


Here are a few of my tools if anyone needs to borrow them this Sunday

- Full 1/2" Metric set (short and deep)
- Full 3/8" Metric set (short and deep)
- Full 3/8" SAE set (deep only)
- Full 1/4" Metric set (short and some deep)
- Cordless Impact Wrench
- Full 1/2" Metric Impact Set
- 1/2" 18" breaker bar (with cheater bar for better leverage)
- Metric ratcheting wrenches (8, 10, 12, 14, 15, 18mm)
- Compression Gauge
- Remote Ignition Trigger
- 3 ton floor jack (not low model)
- 4 jack stands
- Rubber Mallet

Doubt they have electricity but also:
- Corded Dremel
- Corded Heat Gun
- Corded Soldering Set (+ wiring stuff)
- Corded Drill

cool...im bringing my tool box, jacks and stands...

just bring what you think will be neccessary if anything...thanks bro.

I live only a few miles away so I will only bring stuff if people need it.

all we need to do is crack 6 bolts and its done......no big deal

i should have my CEL fix thing by then too...

7 cuz i forgot the o2 sensor

make sure you have new exhaust gaskets on hand.

i dont think he needs new gaskets ? fairly new vehicle with maybe a thousand miles :)
just get some pb blaster and the breaker bar will take care of the rest.

he has 3k on it now.......i think

actually just over 3700 closer to 4000 lol

eh, they are 3-4 bucks a piece, I just figure why take the risk that you muck one of them up and you get pulled over for an exhaust ticket.

its a caless midpipe........its gonna be loud any way