So Whose got a wiring diagram?
#2
Registered
#5
Would anyone be able to upload pictures of there 8 of the same place under the hood (near the master cylinder)? Today I am going to be cutting back the harness to see whats what and I would love to have a picture to look at.
Thanks!
Thanks!
#6
Surf Hard, Drive Hard
Join Date: Feb 2007
Location: Indialantic, Florida
Posts: 7,840
Likes: 0
Received 11 Likes
on
9 Posts
Rodents strike again. Seen about four threads like this!
Damn sure glad I have a pretty tightly sealed up garage for mine.
I'll try to take a pic, but with this broken heel, I don't get around too much at the moment.
What year is your car?
Go48 provided that good link.........it should eventually show you what you need to know.
Damn sure glad I have a pretty tightly sealed up garage for mine.
I'll try to take a pic, but with this broken heel, I don't get around too much at the moment.
What year is your car?
Go48 provided that good link.........it should eventually show you what you need to know.
#7
Its an 04 GT. Looks like i won't need the picture after cutting away more of the harness, It's pretty obvious what goes where. There are three ground wires and the two wires for the brake resouivor (sp?) level.
Now, I do have small crimps. Do I use those or should I solder it and just tape. I have wire of the correct gauges ready (wish I had the same colors too) and everythingelse I need I should have.
Now, I do have small crimps. Do I use those or should I solder it and just tape. I have wire of the correct gauges ready (wish I had the same colors too) and everythingelse I need I should have.
#9
Surf Hard, Drive Hard
Join Date: Feb 2007
Location: Indialantic, Florida
Posts: 7,840
Likes: 0
Received 11 Likes
on
9 Posts
I would solder and shrink wrap them(if you have some), if not......I think I'd run down and get heat shrink at a hardware, electrical, or auto place. I ALWAYS feel better with solder and heat shrink. Buy two sizes.......one to fit over each individual wire and then a size that will fit over all together and shrink them up.
#10
Surf Hard, Drive Hard
Join Date: Feb 2007
Location: Indialantic, Florida
Posts: 7,840
Likes: 0
Received 11 Likes
on
9 Posts
Looooooong F'ing story.
Here's the short version.
Broke it surfing in early April, three months later on the very day the Doc says it's all better, I stumbled going into the house, smashed it down, and fractured in a different spot.
I might be over this all by Christmas! Argh!
Here's the short version.
Broke it surfing in early April, three months later on the very day the Doc says it's all better, I stumbled going into the house, smashed it down, and fractured in a different spot.
I might be over this all by Christmas! Argh!
#11
That really sucks about your ankle. If it makes you feel any better I was running into the house to get the phone but my cat jumped out in front of me and to make a long story short, looks like I have a broken knuckle and or finger. Going for an x-ray in a bit.
I do have heat shrink so thats what I'll do.
Now for my last hurdle... Do I need a new clip? Or how do I do this? I can definitely work out something that I am reasonably sure won't be a problem, but would prefer input from others.
I do have heat shrink so thats what I'll do.
Now for my last hurdle... Do I need a new clip? Or how do I do this? I can definitely work out something that I am reasonably sure won't be a problem, but would prefer input from others.
Thread
Thread Starter
Forum
Replies
Last Post
Danield97
Series I Trouble Shooting
1
09-30-2015 05:59 PM
Learners_Permit
Series I Interior, Audio, and Electronics
8
09-27-2015 07:38 PM