misfire on cylinder 2
#2
He's as bad as Can
Originally Posted by C_RX8
misfire on cylinder 2 .......with a CEL...what do i do?
#3
thanks bro, here it is (P0302 Rear rotor misfire detected Flash/ON 1 or 2 Misfire) ...i will change all spark plugs and then resort to the coil...but will this ruin the motor by driving in this condition.
thanks
chris
thanks
chris
#4
Registered Rep
Join Date: Jan 2005
Location: Largo, FL
Posts: 253
Likes: 0
Received 0 Likes
on
0 Posts
Flashing cell that goes away- random misfire. Will not harm the engine.
Solid cell that doesn't go away- something else. Continual misfire will seriously degrade engine performance, so take it to the dealer for diagnosis.
Solid cell that doesn't go away- something else. Continual misfire will seriously degrade engine performance, so take it to the dealer for diagnosis.
#5
Registered
Join Date: Jul 2004
Location: Northern California
Posts: 2,196
Likes: 0
Received 0 Likes
on
0 Posts
How many miles do you have on those spark plugs, or the car for that mater? You might get it all taken care of free at the dealer. Give us more info about your car.
#6
I dont care...
Join Date: Apr 2005
Location: Pleasantville
Posts: 574
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by C_RX8
thanks bro, here it is (P0302 Rear rotor misfire detected Flash/ON 1 or 2 Misfire) ...i will change all spark plugs and then resort to the coil...but will this ruin the motor by driving in this condition.
thanks
chris
thanks
chris
#7
gents,
thank you for the concern and info.....i currently have 18758 odd miles on the vehicle. my current question is :
1) i recently installed agency power pulley (crankshaft) - following that coincidentally when you would drive it or rev it higher than 4k it(CEL) would flash and go away. could this be the crankshaft pulley causing CEL despite the obd2 saying rotor2 misfire?
2) now that i completely reseted the vehicle by:
-take off battery for 10 minutes
-insert key and turn while pushing odometer reset
-insert key and press brake pedal 20 x or more till the oil pressure does it thang...lol
-then i drive the car slow and allow the dcs and tmps to clear from the dash.....
my question is since my CEL dissappeared does this mean i dont have a problem....?
either way i am going to Mazda which i already made an appt to have them check ....that and compression.....hummmmmn
thank you for the concern and info.....i currently have 18758 odd miles on the vehicle. my current question is :
1) i recently installed agency power pulley (crankshaft) - following that coincidentally when you would drive it or rev it higher than 4k it(CEL) would flash and go away. could this be the crankshaft pulley causing CEL despite the obd2 saying rotor2 misfire?
2) now that i completely reseted the vehicle by:
-take off battery for 10 minutes
-insert key and turn while pushing odometer reset
-insert key and press brake pedal 20 x or more till the oil pressure does it thang...lol
-then i drive the car slow and allow the dcs and tmps to clear from the dash.....
my question is since my CEL dissappeared does this mean i dont have a problem....?
either way i am going to Mazda which i already made an appt to have them check ....that and compression.....hummmmmn
#10
M0D Squad -charter member
Join Date: Jan 2003
Location: Alabama
Posts: 1,498
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by C_RX8
1) i recently installed agency power pulley (crankshaft) - following that coincidentally when you would drive it or rev it higher than 4k it(CEL) would flash and go away. could this be the crankshaft pulley causing CEL despite the obd2 saying rotor2 misfire?
my question is since my CEL dissappeared does this mean i dont have a problem....?
my question is since my CEL dissappeared does this mean i dont have a problem....?
The reason the CEL's (flashing & solid) happened was your PCM noticed a change, and 'assumed' you had a misfire.
#12
hi
i recently bought rx8 04, had engine eplaced on 66k , plugs and coils changed at same time along with radiator......................i was driving around today and had engine misfired .......
i might be doing something like 180km/hr. around 7000 rpm. i had same issue once bfore near around same figures before. i happened whe i was going from 3 gear to 4th gear and i flored the gas.
however when cell was flashing i eased on gas and let rpms droped and drop down to 3rd again after fe mins i start pushing it again just to make sure whts going on as cell disappered. this time i didnt flore gas all the way but no cell was doing 200 almost.
came home even though cell was not on i scanned system it came up with p0302 2 n cylinder misfire no data frame stored though. if u guys could help tht be great and save me a trip 2 dealer and few bucks............thanks.
noticed next morning my exhaust is pretty much blacked out, i wasnt driving my car hard in winter so i have doubt this might have happened due to carbon built up ...............
i recently bought rx8 04, had engine eplaced on 66k , plugs and coils changed at same time along with radiator......................i was driving around today and had engine misfired .......
i might be doing something like 180km/hr. around 7000 rpm. i had same issue once bfore near around same figures before. i happened whe i was going from 3 gear to 4th gear and i flored the gas.
however when cell was flashing i eased on gas and let rpms droped and drop down to 3rd again after fe mins i start pushing it again just to make sure whts going on as cell disappered. this time i didnt flore gas all the way but no cell was doing 200 almost.
came home even though cell was not on i scanned system it came up with p0302 2 n cylinder misfire no data frame stored though. if u guys could help tht be great and save me a trip 2 dealer and few bucks............thanks.
noticed next morning my exhaust is pretty much blacked out, i wasnt driving my car hard in winter so i have doubt this might have happened due to carbon built up ...............
Last edited by manny_rx8; 04-08-2011 at 09:58 AM.
#13
Hi hopefully u guys can help me. i bought a 04 rx8 it has 94k miles the engine was bad which i knew when i bought it. the cooling seals went bad. i bought a re manufactured engine, coils, and plugs from Mazda. i installed them and the car started right up. this is my first rotary. on the first test drive i got a check engine light. the code reader reads P0410 secondary air injection system problem and P0302 rotor 2 misfire and P0300 random misfire. i bought NGK wires installed them still have the same codes after i cleared the codes. the air pump turns on for about a minute when i start the car cold. the car also doesn't seem to do well after 6k rpm under load but in neutral not problem. can someone give me advice?
#14
Registered
iTrader: (2)
Join Date: Oct 2007
Location: Pacific Northwest
Posts: 16,684
Likes: 0
Received 239 Likes
on
109 Posts
Cross posting the exact same post is bad forum ettiquette. Don't worry, people can see your first post. Give them time to respond.
https://www.rx8club.com/showthread.p...12#post4235412
https://www.rx8club.com/showthread.p...54#post4235454
We can see posts as they happen: https://www.rx8club.com/misc.php?product=vblive
https://www.rx8club.com/showthread.p...12#post4235412
https://www.rx8club.com/showthread.p...54#post4235454
We can see posts as they happen: https://www.rx8club.com/misc.php?product=vblive
Thread
Thread Starter
Forum
Replies
Last Post