maxchao

iTrader: (2)

Didn't break the nipple on the radiator? :P

leeboo1211

Nope, I was really worried about that, but the connecting hose had a fair amount of flex and I tried to avoid pulling the nipple in the wrong direction; just try to keep the nipple vertical and use the flex of the hose to get a good angle to pull it off. It was a pain, and had to work slowly, but it came off eventually.

maxchao

iTrader: (2)

lol good job. I pulled it vertically as well but it wouldn't give so I lost patience and pulled really hard...and the nipple broke...then the coolant reservoir replacement became a radiator replacement job.

leeboo1211

Just out of curiosity, how much $ and how long did that take? At some point I would like to swap out the stock radiator for something with better cooling efficiency since I live in FL.

maxchao

iTrader: (2)

I just replaced it with some Ebay stock replicate radiator...for $150. OEM costs $350!

It took me a long time, just because I always take my time on working on the cars...maybe 10 hours? Maybe a mechanic can do it in half of that. (I always take 3 times of time of what a mechanics would take. :P)

nycgps

iTrader: (1)

10 hours ? ...

maxchao

iTrader: (2)

Ha..Like I said I take forever when I work on my car...I just like to play with stuff when I'm in there. Believe or not it took me 18 hours to change 4 shocks lol. (a 4 hour job for mechanics). So yeah if you are good and have right tools devide that number by 3 or 4.

tofu_box

For future references, i found buying the actual hose and just cut the original one around the nipple can *potentially* save u the cost of a new radiator

nycgps

iTrader: (1)

They are doing this plastic bullshit on purpose. Cuz they know 90% of the time people will break it upon removal, easy money right there.

maxchao

iTrader: (2)

This is a good idea. If I ever have to do it again this will be the route that I will take.

Mazurfer

Good tip, not sure why I never thought of that. Hope you don't mind that I stole it for my thread https://www.rx8club.com/showthread.p...53#post3232953 and put it in the first post. Guess I was too consumed with everything else and it didn't actually happen to me, but that beats the crap out of buying a new radiator!

mannerofspeakin

Getting ready to do the replacement. May even add a DIY post with photos as there aren't any yet. To avoid potential nipple breakage can you just remove hose from coolant tank itself leaving it attached to radiator and then add new tank ? Service bulletin says remove from radiator first to avoid breakage.

maxchao

iTrader: (2)

I remember the tank side of the hose is hidden beneath the tank and there was no way that you can reach your hand in there to pull the hose, but I can fit my fingers in to pull on the hose from the radiator side, and that’s how I broke the nipple…

Jethro Tull

iTrader: (6)

You may want to pull the nose to make getting to upper tank nipple easier.

BigGunz

iTrader: (1)

Sorry for resurrecting a year old thread but had to share my experience.

I did a coolant flush and replaced my reservoir today. It actually wasn't as difficult as everyone on here talks it up to be. It was a bit of a pain however, what took forever was doing the flush. I managed to avoid breaking the radiator nipple but I broke the petcock screw on final installation. I called the stealership for price on a "plastic screw" and got quoted $17 and one day for delivery. I said heck to the no and went to Advance Auto who had it for $8 and becoming my automotive savior as of late. Anyway, don't get frustrated with the reservoir........a little patience goes a long way.

I refilled with Prestone 50/50, Redline Water Wetter, & distilled water. Presto.......coolant warning let gone.

Edenney

I know this is an old thread, but perhaps one of the many people who have posted in it could help me out. I'm looking at doing this job myself and I have the new reservoir. After so many people have warned about possibly breaking off the nipple on the radiator, and recommending just cutting the hose and replacing it, I need help identifying precisely which hose I would need to order/replace. I'm not very mechanically inclined and I don't have many tools, so if anybody is likely to break this off it would be me. Could someone who's familiar with this job and the part I'm referring to, perhaps go to Onlinemazdaparts.com, look at the cooling system parts diagram for a 2005 RX8, and tell me which part number is the cooling hose that I would need to order, cut and replace? I've looked at their diagram and I just can't tell which hose it is, as the diagram does not show any hose that connects to a nipple near the top of the radiator best I can tell, much less on the passenger side. There are several hoses in the diagram however. If the hose or a suitable replacement could be purchased from an auto parts store, I'd be open to hearing about that as well (although I'd still really appreciate it if someone could identify the manufacturer's part).

Any other suggestions are welcome, and if anybody happens to be aware of a DIY guide or video for this job I'd really appreciate it (I've searched youtube but couldn't find anything).

Mazurfer

Someone else needs to verify this, but I believe it is 15-184.
If you are just replacing the bottle, there is no need to even disconnect it from the radiator and run the risk of breaking off the nipple. Just remove that hose from the coolant bottle end and put it on the "new" bottle.

While I use OnlineMazdaparts, sometimes they aren't the best at locating parts. Try this link and see if it make more sense?

COOLING SYSTEM. Fits: 2005 Mazda RX-8 | Jim Ellis Mazda

Once you locate it in the picture, then bounce over to the right and scroll down until you see 15184, the click on the blue box beside the $19.16 price and that will show you the stock codes appear to be N3H115184D ; N3H1-15-184A; N3H1-15-184B; N3H115184A; N3H115184B

I tend to use these guys to better identify parts.

But again.................if you are replacing the bottle and not the radiator, and that hose looks in good shape, just leave the radiator end alone and disconnect the bottle end of it, then stick it on the new bottle when you put it in.

RIWWP

iTrader: (2)

Maz, the problem with just disconnecting from the coolant bottle is that you can't really reach that end on a stock 8 unless you twist the coolant bottle out several inches. Doesn't seem like much, but that tension is all it takes to snap the radiator nipple. This is exactly what I attempted to do, and the end results. Just the tension from moving the coolant bottle itself broke the nipple.

Mazmart sells the bottle with the hose included, so you can just cut the hose, which is a cheap preventative measure that works.

Mazurfer

Did mine without breaking it, but then again..........I'm pretty careful. Learned long ago that "Johnny Torque Wrench" usually doesn't pan out......of course unless you do have to just muscle the crap out of something.
With a set of long nose pliers, I was able to release the hose clamp with the bottle still in place, then carefully work that end of the hose off. But, I guess I knew about the dangers on the other end and didn't want to go through that exercise.

Feel free to go up to my post........quote it, and give him your two cents. He may not see this way down here.

2005Shinka

I need some help. I just recently bought some Mishimoto silicone radiator hoses for my 2005 Shinka. I want to know how to change them out. Or do I need to take my car to Mazda and have them do it

Mazurfer

Honestly.......not being a smart ***, but if you don't know the basic steps. You better have someone do it. Are you mechanically inclined at all?

2005Shinka

Yes I have some mechanical knowledge. I can do basic tune ups and change out ignition coils on my rx8. I just can't seem to locate all the hoses without removing my front bumper. I was hoping there is an easier way.

Carbon8

iTrader: (4)

I was not to impressed with the hose kits available from us, IMO this 2 piece kit bull is useless, replaces half the OE upper hose. Thats beyond me. I expected more, in the end I had to piece two kits together to get all hoses replaced, except for the heater core line! Just think by now someone would offer a complete kit, or at least a completer 3 pc kit.

Half of a good thing, stills leaves you with half crap!

2005Shinka

I have a 3 piece radiator hose set. Just wanna make sure I don't have to remove the front end to replace a few hoses

RIWWP

iTrader: (2)

No, you don't. Just drop the splash pan, pull the air box and the battery and you should be able to reach everything.

There are 9 coolant hoses though, and the 3 piece set is usually the major hoses, but that isn't where problems show up.