9krpmrx8

iTrader: (46)

I was never chasing a HP figure but we shall see how it pans out with the new mods. The new wastegate actuator operates way better than the old one so I am hoping that equates to some performance gains. The turbo is now on it's own cooling circuit with it's own heat ex-changer, pump, and failsafe and I have the oil pressure regulator setup all dialed in so the turbo should be happy. The final touches will be the intercooler sprayer setup and water/meth. But those will have to wait until after Christmas.

AAaF

Yes. One of the things I like with my RX8 is the ability to rev high and still keep a flat torque. If I'm going FI, then I'd like to keep this feature as much as possible, but get spool as early as possible, and lag as short as possible(nothing groundbreaking new wishes in other words). Therefore I'd guess the smallest turbo that supports Aux ports intact would be the best solution for my preferences. Does that make it clearer what I'm looking for?

Brettus

iTrader: (2)

It isn't all about the compressor ......... The stock turbine wheel (clipped) works well for the 57trim but is definately wrong for a 60-1 . I imagine a change to the 11 blade turbine wheel would benefit the H3 ,as it does for the 60-1 .

9krpmrx8

iTrader: (46)

Mine also as the 11 blade Turbine.

9krpmrx8

iTrader: (46)

The wheels look different though.

Brettus

iTrader: (2)

/\ looks like he same wheel but the BNR one has been clipped . They mention that they do a "factory clip" on the website.

Brettus

iTrader: (2)

Not sure if this will help but take a look :

https://www.rx8club.com/series-i-maj...60-1-a-255979/

gamaliel31

Coming soon 60-1 inside gt3071R, wastegate 44mm 9psi

Puerto Rico ROTARY POWER

Brettus

iTrader: (2)

Sounds like a plan . Who is doing that for you ?

gamaliel31

I have a goal 380-400 wph. All changes are on the way to that plan.
Custon Turbo job by Turbo outlet in PR $375.00.
My friend from Psychiatrist mechanic and Dyno Jet in Bayamon PR makes me all modifications. Has over 30 years rotary engine experience.

For now I'm going to mount the turbine unchanged, with the external wastegate and reprogramming of the Haltech re 500. The last next step would apex seal, custom port, new pump and some other trick.

gamaliel31

Finished. 40mm blowoff greddy.


Some paint and ready.

Brettus

iTrader: (2)

Nice .
Doing anything with the turbine wheel ? Might pay to ask your guy ...........

gamaliel31

Friend explain better not understand what you mean?

Brettus

iTrader: (2)

Well .......... I put a 60-1 in my Gredddy turbo and left the same turbine in it . That made it spool really slowly . Putting a turbine wheel more suitable for the much larger compressor wheel should make a big difference in both spoolup and overall flow. There might not be anything available for the garrret

Brettus

iTrader: (2)

Any updates on this ? How are you doing the external WG ? Any pics ?

TeamRX8

iTrader: (25)

ajntsa ...

60-1 with that hot side? Not seeing it .... the hot side is too small on a GT3076 for a 2 rotor. 60-1 is essentially a GT35xx compressor and will need something close on the hot side to dpool it up and also not choke


.

gamaliel31

Hey. In these days I will be working with the change of turbine. for now the only upgrade for the gt3071r is gt3076 on cold side.
the turbo upgrade i do after modifying the internal engine. for now i put gt3071r without upgrade.
coming soon new picture.

gamaliel31

new change, now gt3071r be up. using the greddy header. Soon new pictures.