Will MS Wing fit where factory wing holes are?
10-17-2005, 06:53 PM
#1
Registered User
Thread Starter
Join Date: Jul 2005
Posts: 12
Likes: 0
Received 0 Likes
on
0 Posts
Will MS Wing fit where factory wing holes are?
Hi guys, I'm getting ready to get a MS wing and I was wondering if the MS wing will fit where my factory wing holes are or will I have to have those holes filled in and new ones drilled?
Thanks
Thanks
10-17-2005, 09:57 PM
#4
mas than meets the ojo
Join Date: Jun 2005
Location: Fontana, CA
Posts: 95
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by flipstream
Yes... next time, do a search... 
The MS Wing using TWO of the pre-drilled holes from the factory wing. There is one whole that is not used but is covered up with the MS Wing. I would suggest using something to plug the whole or cover it up (maybe just heavy duty 3M tape) to prevent water from leaking through the hole into the trunk lid cavity.
10-17-2005, 10:27 PM
#5
cry me a river...
Join Date: Dec 2003
Location: Syd / Melb
Posts: 4,475
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by flipstream
Yes... next time, do a search... not everyone knows how to do a serach properly
Originally Posted by SnowFl8k
The MS Wing using TWO of the pre-drilled holes from the factory wing. There is one whole that is not used but is covered up with the MS Wing. I would suggest using something to plug the whole or cover it up (maybe just heavy duty 3M tape) to prevent water from leaking through the hole into the trunk lid cavity.
check if there are any rust protection/paint on those pre drilled holes. if not, clean it and use nail polish/touch up paint, so it wont go rust on you later on.....
10-17-2005, 11:37 PM
#6
Originally Posted by EZZY
not everyone knows how to do a serach properly
Last edited by BlueEyes; 10-17-2005 at 11:40 PM.
10-18-2005, 06:42 AM
#7
Originally Posted by BlueEyes
Yeah, right, search engines are really hard to use. I think what you should have said is that most people are too lazy to do a search properly.
10-18-2005, 08:31 PM
#9
Oil Injection
Originally Posted by EZZY
not everyone knows how to do a serach properly
another tip...
check if there are any rust protection/paint on those pre drilled holes. if not, clean it and use nail polish/touch up paint, so it wont go rust on you later on.....
isnt the hood, trunk and 'half doors' all made of aluminium......or is that the new mx5, yeah i guess its the new mx5 that has the aluminium hood and trunk....never mind.
I would paint over the metal, then put tape on the back and front side.
10-18-2005, 09:47 PM
#10
cry me a river...
Join Date: Dec 2003
Location: Syd / Melb
Posts: 4,475
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by BlueEyes
I think what you should have said is that most people are too lazy to do a search properly.
Originally Posted by KYLiquid
isnt the hood, trunk and 'half doors' all made of aluminium......
10-18-2005, 10:57 PM
#11
THE GREAT WHITE
Join Date: Aug 2004
Posts: 825
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by SnowFl8k
Ignoring the comment above - I don't mind taking the time to respond....
Thread
Thread Starter
Forum
Replies
Last Post
TotalAutoPerformance
Vendor Classifieds
12
10-17-2018 09:00 AM
