{ FS } ProClip Mount - $70, chargeable Droid holder ($56) and angled mount ($21)
#1
SOLD ProClip Mount - $70, chargeable Droid holder ($56) and angled mount ($21)
Category: Interior
Price: $70
Private or Vendor Listing: Private Listing
Part Fits (you may select multiples): Series I
Location (US State/Canada/Int): PA
Item Condition: New
Price: $70 plus shipping for the entire package (save $5 for the set)
$21 for mount
$56 for the Droid original holder
Condition: Used, works great
Description: I used the mount part for about 2 years with awesome success. This mount is just phenomenal and I highly recommend it. The holder for the droid I only used for a few months. I changed phones because of work, so I used a iPhone holder which was also great. The installation was pretty simple. I ran the wires through the little hole next to the glove box along with an audio hookup. This mount allows swivel and charge through the fuse box. The mount is solid with a hook and double sided tape.
Manufacturer Description:
Holder:
Motorola Droid (Verizon) - Charging Holder with Tilt Swivel and Straight Power Cord for Fixed Installation with magnet
Avoid cables over your dashboard and always keep your battery fully charged with this high quality custom made holder. It has a neat and discreet design, and keeps your device in an upright position for better reception. A straight power cable is permanently attached to the base of this Holder creating a dock type connection for your device. When your device is slid into the holder it connects to the cable plug. Due to the straight cable you can easily hard wire it behind the dashboard. The Holder angles 15 degrees for optimal viewing. Easily slide your device in/out of the holder. A pas-through connector will allow you to use the headset. No more fumbling around for your device. Provides for safer driving when viewing, accessing and operating your device in your vehicle.
Mount:
Mazda RX 8 - 2004-2008 - ProClip Angled Mount
The ProClip Angled Car Mount attaches on the side of the center console and the face plate is angled towards the driver for optimal viewing. The mount clips into the dashboard seams between the panel sections, providing a very sturdy and tight fit. Average installation time is 2 minutes. No dismantling of the dashboard is required and there is no damage to the vehicle interior!
Last edited by bsteimel; 04-19-2012 at 12:50 PM.
#4
FULLY SEMI AUTOMATIC
iTrader: (9)
how does the cobb attach to the mount in 9ks pic? i dont see your pics in this thread but im looking for a mount for my cobb
#6
Is there any kind of attachment on the back of the device, I've never used one?
Last edited by bsteimel; 04-19-2012 at 10:14 AM.
#7
The Stink w.o The Sause
iTrader: (5)
Would you do local pick up/ drop off? Are you going to this thing by any chance? http://www.tristatetuners.com/forum/....php?p=2120931
Last edited by stinksause; 04-19-2012 at 10:18 AM.
#10
Just good hobby shop Velcro (not walmart or autozone crap) on the back of the AP and on the pro Clip You could also use a stick on cell phone clip if you wanted but good Velcro is better because it's easily removed, double sided tape might be a bitch to remove later.
#11
bump^ are you going to this http://www.tristatetuners.com/forum/....php?p=2120931
#13
FULLY SEMI AUTOMATIC
iTrader: (9)
i want the mount. idk if thats what stink wants but if he doesnt take it i have paypay ready. zip 18444
Thread
Thread Starter
Forum
Replies
Last Post
ShellDude
RX-8 Parts For Sale/Wanted
5
10-01-2015 09:55 PM
Rote8
Series I Interior, Audio, and Electronics
1
09-22-2015 03:43 PM
projectr13b
Series I Do It Yourself Forum
1
09-06-2015 01:04 PM