New parts installed.
04-05-2008, 10:57 PM
#1
Registered
Thread Starter
Join Date: Aug 2007
Location: Hillsboro, Oregon
Posts: 132
Likes: 0
Received 0 Likes
on
0 Posts
New parts installed.
I got my intake, radiator, intake box, and ram air scoop the other week. The RE-Amemiya intake set was quite easy, looks great, sounds even better, and there's been a fair gain in power.
I installed them the other day. Found out that I had to take the intake box out again to be able to get to the radiator hoses. Other than that, it went pretty smoothly. I put the finishing touches on today, some grills for the intake and the center "hole".
The exhaust system will be arriving next week. Hopefully I'll have it in by then.
Also, any drives happening in the Portland area?
I installed them the other day. Found out that I had to take the intake box out again to be able to get to the radiator hoses. Other than that, it went pretty smoothly. I put the finishing touches on today, some grills for the intake and the center "hole".
The exhaust system will be arriving next week. Hopefully I'll have it in by then.
Also, any drives happening in the Portland area?
Last edited by Interpol; 04-05-2008 at 10:59 PM. Reason: Forgot a pic
04-06-2008, 10:40 PM
#3
Wow. Sorry but I can not get over cutting into the bumper for the intake. And then you drilled two holes to attach the license plate with zip ties? Sorry not trying to slam your work.
Which exhaust are you getting? What future mods do you have planned?
There is a poker run in May. Unfortunately not many Portland drives on this board. Check out the rx7club NW section for drives as well.
Which exhaust are you getting? What future mods do you have planned?
There is a poker run in May. Unfortunately not many Portland drives on this board. Check out the rx7club NW section for drives as well.
04-06-2008, 11:09 PM
#4
yeah, i have the same opinion. i couldn't imagine cutting my front bumper to install an intake, then using zip ties to install my license plate. What type of intake would make you cut your bumper? but hey, if you like it....that's all that matters right?
04-07-2008, 09:19 PM
#6
Registered
Join Date: Sep 2006
Location: Puyallup, WA
Posts: 670
Likes: 0
Received 0 Likes
on
0 Posts
I got my intake, radiator, intake box, and ram air scoop the other week. The RE-Amemiya intake set was quite easy, looks great, sounds even better, and there's been a fair gain in power.
I installed them the other day. Found out that I had to take the intake box out again to be able to get to the radiator hoses. Other than that, it went pretty smoothly. I put the finishing touches on today, some grills for the intake and the center "hole".
The exhaust system will be arriving next week. Hopefully I'll have it in by then.
Also, any drives happening in the Portland area?
I installed them the other day. Found out that I had to take the intake box out again to be able to get to the radiator hoses. Other than that, it went pretty smoothly. I put the finishing touches on today, some grills for the intake and the center "hole".
The exhaust system will be arriving next week. Hopefully I'll have it in by then.
Also, any drives happening in the Portland area?
04-09-2008, 03:08 PM
#8
Registered
Thread Starter
Join Date: Aug 2007
Location: Hillsboro, Oregon
Posts: 132
Likes: 0
Received 0 Likes
on
0 Posts
Why? For speed.
I was gonna wait on the dyno until the RE-Amemiya exhaust (Super Dolphin Tail, exhaust manifold and sport cat) arrives and I get to install it.
For other mods? I'm going to be getting the RB lightened rotor assembly, Blitz S/C, a port an polish from Mazdatrix, the Hymee ECM, full roll cage, Auto-exe sub frame braces, a better LSD, R-Magic lip/front, RE-Amemiya side and rear diffusers, a GT wing and more. Basically it's going to be a time attack monster as soon as summer break rolls around.
The zip ties are only temporary, I'm gonna figure out a different way to attach the plate. It also looks much better in person.
I was gonna wait on the dyno until the RE-Amemiya exhaust (Super Dolphin Tail, exhaust manifold and sport cat) arrives and I get to install it.
For other mods? I'm going to be getting the RB lightened rotor assembly, Blitz S/C, a port an polish from Mazdatrix, the Hymee ECM, full roll cage, Auto-exe sub frame braces, a better LSD, R-Magic lip/front, RE-Amemiya side and rear diffusers, a GT wing and more. Basically it's going to be a time attack monster as soon as summer break rolls around.
The zip ties are only temporary, I'm gonna figure out a different way to attach the plate. It also looks much better in person.
04-09-2008, 06:41 PM
#9
Drive Master
Join Date: Nov 2003
Location: Redmond
Posts: 1,670
Likes: 0
Received 0 Likes
on
0 Posts
If you don't have a dyno for your current mods, you didn't gain an power. If you don't have a baseline from before the mods, you didn't gain any power.
Sorry, but I think it more likely you're butt dyno is showing "a fair gain in power" due to the increased surface area of the but to seat interface resulting from the lightened wallet mod. Not hating, but you can't make a claim without proof.
Sorry, but I think it more likely you're butt dyno is showing "a fair gain in power" due to the increased surface area of the but to seat interface resulting from the lightened wallet mod. Not hating, but you can't make a claim without proof.
06-17-2008, 02:09 AM
#11
OMGITM!
iTrader: (15)
Join Date: Jan 2006
Location: Sunny Southern California
Posts: 3,513
Likes: 0
Received 6 Likes
on
6 Posts
Why? For speed.
I was gonna wait on the dyno until the RE-Amemiya exhaust (Super Dolphin Tail, exhaust manifold and sport cat) arrives and I get to install it.
For other mods? I'm going to be getting the RB lightened rotor assembly, Blitz S/C, a port an polish from Mazdatrix, the Hymee ECM, full roll cage, Auto-exe sub frame braces, a better LSD, R-Magic lip/front, RE-Amemiya side and rear diffusers, a GT wing and more. Basically it's going to be a time attack monster as soon as summer break rolls around.
The zip ties are only temporary, I'm gonna figure out a different way to attach the plate. It also looks much better in person.
I was gonna wait on the dyno until the RE-Amemiya exhaust (Super Dolphin Tail, exhaust manifold and sport cat) arrives and I get to install it.
For other mods? I'm going to be getting the RB lightened rotor assembly, Blitz S/C, a port an polish from Mazdatrix, the Hymee ECM, full roll cage, Auto-exe sub frame braces, a better LSD, R-Magic lip/front, RE-Amemiya side and rear diffusers, a GT wing and more. Basically it's going to be a time attack monster as soon as summer break rolls around.
The zip ties are only temporary, I'm gonna figure out a different way to attach the plate. It also looks much better in person.
06-19-2008, 12:16 AM
#12
Registered User
Join Date: Jun 2007
Location: Hood River, Oregon
Posts: 50
Likes: 0
Received 0 Likes
on
0 Posts
hey bro dont listen to these ******* their just playin..lol...congrats. would you recommend the ms flywheel or other? oh and i think i saw a winning blue front bumper on craigslist the other day..u know jus incase you change your mind...but again good job and congrats...let us know on the dyno results. good luck.
06-23-2008, 03:56 AM
#13
Registered
Thread Starter
Join Date: Aug 2007
Location: Hillsboro, Oregon
Posts: 132
Likes: 0
Received 0 Likes
on
0 Posts
I have the RE-Amemiya manifold to muffler, Nardi Classico 330m suede, Rapfix II quick release, and NRG short hub, HKS Twin Power DLI II ignition amplifier, Optima Yellow Top installed. I also have some RT-615's on (245/40 R18)
Defi gauges (Oil T, Oil P, EGT, VSD X, Defi-Link), Bride GIAS Andromeda seats, Project Mu big brake kit for the front and pads and rotors for the rear, Cusco 6pt rollcage, Cobb Tuning AccessPort, 5pt strap and pads for the Takatas, a spin/turn ****, NGK Iridium plugs, and HKS plug wires. These are ordered and will be arriving steadily over the next month.
I still haven't gotten a dyno, been too busy and I'm now waiting for the AccessPort so I can have some tuning done at the same time.
Defi gauges (Oil T, Oil P, EGT, VSD X, Defi-Link), Bride GIAS Andromeda seats, Project Mu big brake kit for the front and pads and rotors for the rear, Cusco 6pt rollcage, Cobb Tuning AccessPort, 5pt strap and pads for the Takatas, a spin/turn ****, NGK Iridium plugs, and HKS plug wires. These are ordered and will be arriving steadily over the next month.
I still haven't gotten a dyno, been too busy and I'm now waiting for the AccessPort so I can have some tuning done at the same time.
06-24-2008, 03:48 AM
#16
Registered
Thread Starter
Join Date: Aug 2007
Location: Hillsboro, Oregon
Posts: 132
Likes: 0
Received 0 Likes
on
0 Posts
Here's those pics I promised. My gauges have also arrived and I'll pick them up tomorrow from Speed Concept.
The manifold
The cat with old manifold
The HKS Twin Power DLI II
Nardi Classico 330mm with black suede
Works Bell Rapfix II detached
Some more of the exhuast taken today
And a pic from the beach house after the TNT cruise
The manifold
The cat with old manifold
The HKS Twin Power DLI II
Nardi Classico 330mm with black suede
Works Bell Rapfix II detached
Some more of the exhuast taken today
And a pic from the beach house after the TNT cruise
Last edited by Interpol; 06-24-2008 at 04:26 AM.
06-28-2008, 06:40 PM
#24
Registered
Thread Starter
Join Date: Aug 2007
Location: Hillsboro, Oregon
Posts: 132
Likes: 0
Received 0 Likes
on
0 Posts
It seems to have a gain in mpg if I drive with reservation. But, it is toooo much fun to rail it.
I also have the oil temp, oil pressure and VSD X wired up. Waiting on a rev adapter for the VSD X to work completely. Next week, I'll have time to get the exhaust temp all wired up. I'll post pics once everything is all neat and tidy.
I also have the oil temp, oil pressure and VSD X wired up. Waiting on a rev adapter for the VSD X to work completely. Next week, I'll have time to get the exhaust temp all wired up. I'll post pics once everything is all neat and tidy.
