{ FS } Greddy Turbo Kit with MM GT3076r Upgrade for Sale - $3000
10-18-2015, 02:27 AM
#1
Greddy Turbo Kit with MM GT3076r Upgrade for Sale - $3000
SOLD
Selling my Greddy Turbo kit with system extras. I purchased this kit in May of 2014 from another RX-8 Owner. The kit has been previously used but the Turbo was newly rebuilt and hasn’t been used since then. Over the last year and a half I have been preparing for the install by getting gauges and sensors installed, setting up a good N/A tune, learning to tune (Attended Kane’s course in June 2014), and gathering other necessary parts.
Here is a list of the other parts I have accumulated for the kit:
1. Greddy Spec B Boost Controller
2. Greddy Blow-off Valve with required flanges in compression pipe
3. Autometer Oil Pressure Gauge w/ pressure sender
4. Glow Shift Exhaust Temperature Gauge with Sensor
5. Heat Insulation Sheet 4’ x 8’ with back adhesive
6. Insulation Tape
7. Manifold Insulation Wrap
8. New set of stainless fasteners for kit
9. New Stainless T-Bolt Clamps
10. New Urethane Hose couplings
The kit is missing a few minor items:
1. Intercooler Mounting Brackets,
2. Bracket to stabilize exhaust manifold
3. E-manage system (but you don’t want it) so a COBB Accessport or MazdaEdit tuning device and software will be require to do a proper job.
4. -4 AN oil feed line also isn’t included but can be easily purchased at several autoparts locations.
5. Flexible air pump line. (Also not necessary as you just perform the pump delete mod)
The reason I am selling is that I started autocross this year and I am loving it. Unfortunately, a turbo would put me into Street modified class and I don’t want to spend the money to get the 8 to a place where I would be competitive locally (And beyond that I am not even sure). I am having the most fun with my car when I autocross and so I will focus on staying in Street touring and being a little successful.
If you have any questions let me know. Obviously its easier not to ship but I am open to it. USD to CAD rates are good for any Americans right now if they want to jump on this...
Selling my Greddy Turbo kit with system extras. I purchased this kit in May of 2014 from another RX-8 Owner. The kit has been previously used but the Turbo was newly rebuilt and hasn’t been used since then. Over the last year and a half I have been preparing for the install by getting gauges and sensors installed, setting up a good N/A tune, learning to tune (Attended Kane’s course in June 2014), and gathering other necessary parts.
Here is a list of the other parts I have accumulated for the kit:
1. Greddy Spec B Boost Controller
2. Greddy Blow-off Valve with required flanges in compression pipe
3. Autometer Oil Pressure Gauge w/ pressure sender
4. Glow Shift Exhaust Temperature Gauge with Sensor
5. Heat Insulation Sheet 4’ x 8’ with back adhesive
6. Insulation Tape
7. Manifold Insulation Wrap
8. New set of stainless fasteners for kit
9. New Stainless T-Bolt Clamps
10. New Urethane Hose couplings
The kit is missing a few minor items:
1. Intercooler Mounting Brackets,
2. Bracket to stabilize exhaust manifold
3. E-manage system (but you don’t want it) so a COBB Accessport or MazdaEdit tuning device and software will be require to do a proper job.
4. -4 AN oil feed line also isn’t included but can be easily purchased at several autoparts locations.
5. Flexible air pump line. (Also not necessary as you just perform the pump delete mod)
The reason I am selling is that I started autocross this year and I am loving it. Unfortunately, a turbo would put me into Street modified class and I don’t want to spend the money to get the 8 to a place where I would be competitive locally (And beyond that I am not even sure). I am having the most fun with my car when I autocross and so I will focus on staying in Street touring and being a little successful.
If you have any questions let me know. Obviously its easier not to ship but I am open to it. USD to CAD rates are good for any Americans right now if they want to jump on this...
Last edited by AreAxeAte; 10-26-2015 at 04:11 PM.
10-18-2015, 10:03 AM
#3
SPOOLN8
iTrader: (1)
Join Date: Nov 2008
Location: Edmonton, Alberta, Canada
Posts: 2,225
Received 208 Likes
on
156 Posts
$3000 CAD
The kit is missing a few minor items:
1. Intercooler Mounting Brackets, MINOR
2. Bracket to stabilize exhaust manifold Do you meant the bracket for the downpipe? If so MINOR
3. E-manage system (but you don’t want it) so a COBB Accessport or MazdaEdit tuning device and software will be require to do a proper job. AP all the way!
4. -4 AN oil feed line also isn’t included but can be easily purchased at several autoparts locations. MINOR
5. Flexible air pump line. (Also not necessary as you just perform the pump delete mod) JUST DELETE IT!
The kit is missing a few minor items:
1. Intercooler Mounting Brackets, MINOR
2. Bracket to stabilize exhaust manifold Do you meant the bracket for the downpipe? If so MINOR
3. E-manage system (but you don’t want it) so a COBB Accessport or MazdaEdit tuning device and software will be require to do a proper job. AP all the way!
4. -4 AN oil feed line also isn’t included but can be easily purchased at several autoparts locations. MINOR
5. Flexible air pump line. (Also not necessary as you just perform the pump delete mod) JUST DELETE IT!
Dean waiting for you to pull the trigger on this!!! ..... No customs, minor shipping costs, good price. The money you'd save on gauges, BOV, and EBC you could buy a better intake and get the AP!
Last edited by RotaryMachineRx; 10-18-2015 at 10:09 AM.
10-19-2015, 10:54 PM
#4
This jerk is unwilling to make a deal! I offered for a straight across trade for my BHR header! I mean, if that's not doing a guy a favour, I don't know what is. /s 
In all honesty, I know AreAxeAte from way back, and he's a great guy. I'm just a little sad he's not going to have a turbo 8 to burn around in.
In all honesty, I know AreAxeAte from way back, and he's a great guy. I'm just a little sad he's not going to have a turbo 8 to burn around in.
10-20-2015, 11:53 AM
#5
Ha Ha. You worried me for a second there BWilk. I was thinking someone offered me a deal I didn't know about.
BHR header would be nice but it will still take me out of STX and put me into DSP and I just don't know if I want to do that. Thanks anyhow!
BHR header would be nice but it will still take me out of STX and put me into DSP and I just don't know if I want to do that. Thanks anyhow!
Thread
Thread Starter
Forum
Replies
Last Post
