For Sale or Trade a set of Silver Enkei 18x7.5" RPF1's, w/48et. These wheels have aprox 1800 miles. I'm including New Mazda hub rings and Enkei blue alloy valve stems. I'm thinking about going back to OE / OEM RX-8 wheels. RPF1's are great wheels @ 17lbs. They sell for $1,200 w/ CF center caps from Tire Rack + shipping. Asking $725.00 plus shipping from Mesa AZ 85203. ( No Tires! ) I still have the Enkei boxs.
Sorry there is now about a 2 3/8" curb mark just into the silver paint, about 3/16" of this mark is into the alloy. I need to get some rubbing compound to see if it will clean up.

email @ hayrandyl@cox.net

Got PM, Yes I can.

Thanks

Anyone like them?

any reason why you went with thinner wheels and lower profile tires than stock? Or were these ran on a different car?

Hm.. looks like you're selling wheels off of your TSX on an RX-8 forum, haha. Try the Honda forums, but even those guys don't like 7.5 +48s anymore.

Hm.. looks like you're selling wheels off of your TSX on an RX-8 forum, haha. Try the Honda forums, but even those guys don't like 7.5 +48s anymore.

i agree, try tsxclub, rsxclub, and nasioc (some wagon owners might like these)

any reason why you went with thinner wheels and lower profile tires than stock? Or were these ran on a different car?

Come on people! There off another Mazda. "Honda," I didn't think Honda had a 67.1mm hub center? Can't post on the Mazda 3 site because there Mods are asses!
And why would I be looking for 8 OE rear sway bar?

Thanks,
MM

The TSX runs a 64.1 so the wheels would fit with or without the hubcentric rings.

hubcentric rings are cheap, and you can knock em out with a hammer and replace them with proper ones in less than 60 seconds. its the decrease in width thats the only issue i can see.

hubcentric rings are cheap, and you can knock em out with a hammer and replace them with proper ones in less than 60 seconds. its the decrease in width thats the only issue i can see.

And the lost of over 5 lbs per corner. (for the wheels) Plus no need to knock out the proper alloy hub rings.

P, I see your still mad because I didn't give you my old Passport X50.

Hm.. looks like you're selling wheels off of your TSX on an RX-8 forum, haha. Try the Honda forums, but even those guys don't like 7.5 +48s anymore.

really,

funny. dont make me attack your many posts with silly offsets at the same time!!

dont get me started.

i think vendor status might be something to think about.. really 3 sets of wheels for sale at the same time???? 2 posts.

btw, minimeg, is honest!

beers :beer:

I don't believe I'm selling anything in the size of 7.5 +48 but if I am, please enlighten me.

I don't believe I'm selling anything in the size of 7.5 +48 but if I am, please enlighten me.

Hey guy, Take it easy, Please!
I don't want this to get out of hand. It's true the wheels where not on an RX-8. When we lived in NM I went to some local Solo's with the RX-8 club. Great bunch too.
But they where mounted on a Mazda. I remove these wheels to install a set of 16x8 FD wheels non-reinforiced @ about 14 lbs then had them podwer coated Flat Black. My BETTER HALF i.e. Meg wants The OE 8 wheels put back on the Galaxy Gray car.

Oh, THANKS for the kind words Swoope.

Cheers,
MM

Haha, I didn't mean to come off as hostile, I just wanted to know where I was selling the wheels he claimed I was.

He also claimed I was attacking him with some kind of offset? I don't know what that means but I've never seen the username in my life I think he must be confused..

Haha, I didn't mean to come off as hostile, I just wanted to know where I was selling the wheels he claimed I was.

He also claimed I was attacking him with some kind of offset? I don't know what that means but I've never seen the username in my life I think he must be confused..

the wheels mention will fit fine.. and the guy really does have a mazda..

and you? you are selling 19s and stuff with offsets that really dont make sense?

and wait. at three or four sets at a time, so who are you to judge..

please take the time to read the fine print in the stickys..

just fyi.

beers :beer:

I've already talked to a mod, so I appreciate the concern.

As for 19s with offsets that don't make sense? My 19s are +38 all around.
No one said they wouldn't fit the RX-8 but selling 7.5 +48 all around, I mean come on that's a little narrow + non staggered + higher offset than most people want. Face it, it's the truth.

I'm done posting in here because you obviously mistake everything anyone says as an insult. Good day to you.

I've already talked to a mod, so I appreciate the concern.

As for 19s with offsets that don't make sense? My 19s are +38 all around.
No one said they wouldn't fit the RX-8 but selling 7.5 +48 all around, I mean come on that's a little narrow + non staggered + higher offset than most people want. Face it, it's the truth.

I'm done posting in here because you obviously mistake everything anyone says as an insult. Good day to you.


really.

the op stuff will fit fine.. as to the 18 x7.5 vs your 19 inch stuff.. and if you are done here good...


honest is honest.

beers :beers:

so wait, an 18x7.5 +48 isn't silly but a 18x9/8 +38 is?

Bump... Now that the waters have settle down I'm going to try again.

Thanks for looking!
Randy & Meg

so wait, an 18x7.5 +48 isn't silly but a 18x9/8 +38 is?

at 17 lbs. yes..

chamber should have never entered this thread.

btw, to all.

an 18 x 7.5 +45 will work with a 245 40 18 for track days. is it perfect, no. but it does work.. but an r compound 245 35 18! :)

and at 17 lbs.

well shameless bump.

beers :beer:

at 17 lbs. yes..

chamber should have never entered this thread.

btw, to all.

an 18 x 7.5 +45 will work with a 245 40 18 for track days. is it perfect, no. but it does work.. but an r compound 245 35 18! :)

and at 17 lbs.

well shameless bump.

beers :beer:

Swoop,
Thanks for the bump. Your a good guy and I like your beer holder. (as Meg slaps the back of my head) Ouch!

Swoop,
Thanks for the bump. Your a good guy and I like your beer holder. (as Meg slaps the back of my head) Ouch!

no problem.

you have been here for a while. and have a miata..

i would buy them if i did not have that covered.

:)

beers :beer:

lol @ "now that its calmed down" then swoopes instant quote and re-stirring of the shit pot....

funny stuff. i would like the rpf1's if they were 7.5

i would like the rpf1's if they were 7.5

:confused: ! They are 7.5.

oh lol my bad, i meant if they were not. I actually could use them on my rx7, but they would cost more than i have in the whole car+ motor rebuild :P

oh lol my bad, i meant if they were not. I actually could use them on my rx7, but they would cost more than i have in the whole car+ motor rebuild :P

You have a $800 RX-7? :rolleyes: sorry but that's one hell of a deal!

Interested. How much to ship to 91010?

PMed,

Thanks.

I'm getting some feedback for the M3 guys. I know this is the same size wheels and all from the MS3 cars.

Thanks,
Randy & Meg